BONDING AGENTS

Description

KUT BOND EP is a multi-purpose adhesive based on solvent-free epoxy resins. It has exceptional adhesive properties and is supplied as a two-pack material which on mixing cures to high strength, oil, water, and chemical resisting surface.

Uses

It is designed as a bonding agent for fine and coarse aggregate, which must be clean and dry, to form a chemical-resistant mortar granolithic flooring or screed. It is recommended for use as an economical epoxy bonder for old to new freshly laid concrete or screed. It may also be used as a primer for epoxy floor coating, screeds, and bonding sprinkled on aggregate. It is used as a general-purpose bonding agent for common construction materials including concrete, ceramics, glass, metals, asbestos, timber, plastics, etc.

Description

KUT BOND PVA is a modified polyvinyl acetate emulsion formulated especially for use as a bonding aid with gauging water for plaster and cementitious mortars not exposed to dampness or water. It is the white, non-toxic, non-inflammable liquid of medium viscosity which dries to a transparent film.

Uses

Used for improving and bonding floor topping, cement renderings, and mortars, and repair of damaged and spalled concrete for dry exposure conditions. It is used as tile adhesive when mixed with cement and blended sands. It is recommended as a multi-purpose adhesive, a plaster bonding agent, a primer for overcoating bitumen with oil-based paints, for dust proofing floor screeds, and for friable concrete flooring.

Description

KUT BOND TN is a specially formulated non–shrink, non-sag, solvent-free epoxy resin-based system blended with fine inert fillers. It is supplied as a two-component material in pre-weighed quantities ready for on-site mixing and use.

Uses

KUT BOND TN is primarily intended as a bonder for old concrete to new freshly laid as well as old concrete and cementitious repair products.

Description

KUT EPOXYBONDER-“OTN” is a specially formulated epoxy resin-based system blended with fine Inert fillers. It is supplied as a two-component material in pre-weighed quantities ready for on-site mixing and use.

Uses

KUT EPOXYBONDER-” OTN” is primarily intended as a bonder for old concrete to new freshly laid concrete. It may also be used as a primer for placing KUT EPOXYMORTARS on dry as well as damp substrates.

Description

KUT FLEXI is a specially formulated liquid polymer emulsion recommended for use as an additive for thin bed mortars in installing tile, paver, brick, marble, and stone. These mortars are suitable for interior and exterior use over concrete as well as masonry-type surface. KUT FLEXI is suitable for applications that will be subject to continuous underwater immersion such as swimming pools, fountains, etc.

Uses

KUT FLEXI-based mortars are used for installing ceramic tiles, mosaic tiles, quarry tiles, natural stone, marble, terrazzo tiles, glass mosaic tiles, and thin bricks. These mortars are recommended for use over new and old concrete, masonry surfaces, gypsum plaster, concrete blocks, concrete screeds, gypsum wallboard, concrete plaster, calcium silicate blocks, and existing terrazzo tiles. It is recommended for use with KUT SUPERCOAT No.2, KUT TILE MORTAR, and some other KUT products.

Description

KUT TILE ADHESIVE-EG is supplied as a ready to use one component white/grey powder requiring only the addition of water to produce a cohesive, sticky highly adhesive thin bed tile adhesive. KUT TILE ADHESIVE-EG powder is a blend of white & grey cement, selected fine sands, water reducing chemicals, special polymers, water retention agents to enhance workability and ease of application.Available in two colors-White and Grey.

Uses

KUT TILE ADHESIVE-EG white is recommended for following application:(i) Fixing ceramic tiles on walls and floors.(ii) Bonding quarry tiles direct on concrete or sand cement renderings and clean non-glazed old terrazzo tiles. (iii) Fixing tiles over timber and existing vinyl tiles if the surfaces are properly cleaned and primed with a brush coat of KUT FLEXIBOND. KUT TILE ADHESIVE-EG is specially recommended for fixing porous and white coloured tiles. However due care should be taken to ensure proper levels and that the thickness in such application does not exceed 12mm. Both grades of KUT TILE ADHESIVE-EG are suitable for interior as well as exterior conditions.

Description

KUT SBR NO.1 is a highly concentrated styrene butadiene polymer emulsion modified with a blend of special auxiliary chemicals. KUT SBR NO.1 can be used for indoor as well as outdoor applications as the system is resistant to hydrolysis.

Uses

It is used as an integral adhesive and admixture to produce at the job site polymer modified cementitious mixes.  It is used in preparing thick tile bedding mortar.  It is recommended for use in bonding polystyrene panels with cementitious mortars.  It is used for general repair of damaged and spalled concrete. It also improves the qualities of the flooring screeds and increases the waterproofing and chemical resistance of cementitious mixes used as renders.  It is used as primer/sealer for cementitious repair products and cementitious floorings.

Description

KUT SBR NO.1 is a highly concentrated styrene butadiene polymer emulsion modified with a blend of special auxiliary chemicals. KUT SBR NO.1 can be used for indoor as well as outdoor applications as the system is resistant to hydrolysis.

Uses

It is used as an integral adhesive and admixture to produce at the job site polymer modified cementitious mixes.  It is used in preparing thick tile bedding mortar.  It is recommended for use in bonding polystyrene panels with cementitious mortars.  It is used for general repair of damaged and spalled concrete. It also improves the qualities of the flooring screeds and increases the waterproofing and chemical resistance of cementitious mixes used as renders.  It is used as primer/sealer for cementitious repair products and cementitious floorings.

Description

KUT GEL EP is a thixotropic two component epoxy resin with exceptional adhesive and sealing characteristics. The base component is bluish White coloured and the hardner component is brownish yellow to facilitate ease of mixing.

Uses

It is designed for use as a surface sealant for crack injection systems. It is also used as bonding agent for common construction materials including asbestos, glass, timber and some plastics. It is also recommended for filling blowholes and minor surface irregularities prior to application of gap epoxy resin based coating systems.

Description

KUT BOND PVA-MG is a modified polyvinyl acetate emulsion formulated especially for use as a bonding aid with gauging water for plaster and cementitious mortars not exposed to dampness or water. It is the white, non-toxic, non-inflammable liquid of medium viscosity which dries to a transparent film

Uses

Used for improving and bonding floor topping, cement renderings, and mortars, and repair of damaged and spalled concrete for dry exposure conditions. It is used as tile adhesive when mixed with cement and blended sands. It is recommended as a multi-purpose adhesive, a plaster bonding agent, a primer for overcoating bitumen with oil-based paints, for dust proofing floor screeds, and for friable concrete flooring.