Concrete Repair

Description

KUT EPOXY MORTAR FC is thixotropic solvent-free, with two components based on epoxy resins, graded fillers, and thixotropic agents, specially formulated to meet a range of service temperatures from 25°C to 60°C. The base component is white colored and the hardener is black to facilitate ease of mixing

Uses

For filling blow holes, making fair slightly damaged concrete, and eliminating minor irregularities before painting or coating. Highly recommended for repair of structures that will be permanently submerged in water, sea water like water intake areas in power plants, etc. • As an adhesive for bonding pre-fabricated concrete bridge segments. • As an anode shield and cavity filler.

Description

KUT EPOXY MORTAR - HB is a special blend of fillers and solvent-free epoxy resin, designed for speedy and permanent repairs to concrete, particularly in vertical or overhead situations. The mixed material is applied to a suitably prepared surface and quickly cures to form an impermeable repair unaffected by most forms of a chemical attack. It is supplied as a three-pack material in pre-weighed quantities ready for on-site mixing and use

Uses

For speedy and permanent repairs to concrete structures, especially in overhead and vertical situations where “High Build” repairs are required and impermeability to water and resistance to aggressive chemicals are essential. For emergency repairs to concrete columns, lintels, and roof-beam faces, provide a dense impermeable finish and protect the embedded reinforcing steel.

Description

KUT FAIRING COAT is a concrete-grey or off-white, single-component mortar, based on a blend of portland cement, graded silica sands, water-reducing agents, and compatible water-resistant polymers. The product is designed to give good adhesion and cohesion in a plastic state and low water requirement resulting in low porosity and long durability...

Uses

KUT FAIRING COAT is used for producing a fair-faced concrete appearance after patch repairs to walls, for leveling uneven surfaces, filling honeycombs in precast units and walls, and as a leveling compound to prepare for painting or coating. It is suitable for use in marine structures.

Description

KUT FASTCRETE is a fast-setting concrete patching material composed of special cement, fine aggregate, and selected plasticizing admixture and fibers, requiring the addition of potable water only for mixing. It produces high early strength and achieves the initial set in 20 to 30 minutes, and the final set in 45 minutes. Repaired areas may be opened to traffic in 2 - 2:30 hours.

Uses

KUT FASTCRETE is specifically formulated as a semi-flowable material for the rapid patching of horizontal concrete surfaces such as airport runways, expressways, highways, bridge decks, streets, sidewalks, parking decks loading docks, and floors.

Description

KUT FILLET PAK is supplied as a ready-to-use two-component product consisting of a dry powder (Part A) requiring only the addition of the liquid aqueous polymer (Part B) to produce cohesive easily applied mortar. The dry powder is a careful blend of cement, graded sands, Microsilica, water-reducing agents auxiliary/modifying polymer, polypropylene micro fibers, and a polymer (Part B) component KUT FLEXI to enhance the general characteristics of the repair mortar. It is designed to give excellent adhesion to concrete in the plastic state and deliver low porosity and long durability repair mortar. The KUT FILLET PAK is modified with expansive agents to compensate for the shrinkage of this mortar in the plastic state and also during the first 3 days of the hardening period.

Uses

KUT FILLET PAK is a multi-application polymer-modified cementitious mortar for structural repair and reinstatement of damaged concrete. It is used to form concave fillets or covers between parapet walls and roofs. It is used for packing and filling junction fillet strips or chisel-opened gaps between walls and floors in water-leaking basements and tie-rod holes in concrete structures. It is used in marine environments to repair damaged concrete, beams, and columns.

Description

KUT SUPERCOAT No. I is supplied as a ready to use dry powder requiring the addition of only clean water to produce at the job site a highly cohesive fibre reinforced easily applied repair mortar. KUT SUPERCOAT No. I is formulated on a blend of portland cement, Microsilica, non-metallic reinforcing fibres, selected graded aggregates, water reducing chemicals, shrinkage compensating agents and new technology synthetic resin dry polymers. KUT SUPERCOAT No. I mixed mortar delivers excellent adhesive and cohesive characteristics. It is a low porosity and long durability mortar which provides special resistance to the passage of water, the ingress of chlorides and polluted industrial dampness and can be used in both vertical and overhead applications. It is recommended for repair of damaged structural concrete exposed to marine environmental corrosive conditions in both inland and offshore installations.

Uses

KUT SUPER COAT No. I has been formulated specially to repair damaged structural concrete and all types of masonry under a wide range of normal, industrial and marine environmental exposures. It is used for reinstatement of damaged concrete, walls, soffits and columns in overhead as well as vertical applications. It is recommended for internal as well as exterior application for inland and offshore marine environments. It will provide great value to contractors involved in general repair works of structural concrete for port authorities, airports and military installations.

Description

KUT SUPERCOAT No. II is supplied as a ready-for-use 2-component product consisting of a dry powder and a specially formulated aqueous synthetic resin polymer which after mixing produce a highly cohesive easily applied repair mortar. This product is formulated as a new technology blend of cements, microsilica, non metallic reinforcing fibres, selected graded aggregates water reducing chemicals and shrinkage compensating auxiliary agents. The special liquid polymer KUT FLEXI is an aqueous binder modified with auxiliary chemical agents to improve the final properties of KUT SUPERCOAT No. II. The KUT SUPERCOAT No. II mixed polymer mortar has excellent adhesive and cohesive characteristics. It is a low porosity and long durability mortar which can be used in both vertical and overhead repair works.

Uses

It is used for the reinstatement of damaged concrete, walls, soffits, beams and columns. It is recommended for internal as well as exterior application for inland and marine environmental exposure.

Description

KUT RENCON ‘S’ is supplied as a ready to use dry powder requiring only the addition of water to produce cohesive easily applied mortar. The product is a careful blend of portland cements, graded silica sands, shrinkage compensating agents silica fume, water reducing agents and compatible water resistant polymers. The product is designed to give good adhesion and cohesion in, the plastic state and low water requirement resulting in a non-shrink low porosity mortar with high compressive strength and durability.

Uses

KUT REINCON ‘S’ is recommended for structural reinstatement of damaged concrete for beams and columns in inland and marine environments, and as a general purpose repair mortar for concrete floors and highly trafficked areas

Description

It is supplied as a ready to use dry powder requiring only the addition of water to produce a cohesive and easy to apply mortar. KUT OVERHEAD MORTAR is a new technology polymer modified blend of Portland cement, selected graded sands, Microsilica, non-metallic special reinforcing fibres, light weight micro aggregates, water resistant polymer sand water reducing agents. It is formulated for vertical and also overhead applications in outdoor and indoor repair works. KUT OVERHEAD MORTAR is specially made to produce a cohesive highly adhesive repair mortar with low water requirement. It produces a low porosity, long durability repair mortar.

Uses

It is made for general purpose wide range multi-application repairs and patching of damaged concrete walls, soffits, columns, overhead beams, spalled concrete, roof, parapet walls etc.

Description

KUT FLOWCRETE is supplied as a ready-to-use cement aggregate/sand mix requiring only the addition of water to produce a free-flowing repair concrete. It is a careful blend of Portland cement, graded aggregate, sand, micro silica, water-reducing agents, and auxiliary expansive modifying agents to compensate for the shrinkage in both the plastic and the hardened states.

Uses

KUT FLOWCRETE with dual expansion characteristics has been engineered for a wide range of applications. It is formulated for free flowing in between highly congested reinforcement located in difficult-to-reach areas. The free-flowing consistency of KUT FLOWCRETE ensures its penetration into honeycombed concrete and defective deteriorated concrete filling all voids with high-performance repair concrete. It is suitable for use in the marine environment.