Description KUT EPOXY MORTAR FC is thixotropic solvent-free, with two components based on epoxy resins, graded fillers, and thixotropic agents, specially formulated to meet a range of service temperatures from 25°C to 60°C. The base component is white colored and the hardener is black to facilitate ease of mixing Uses For filling blow holes, making fair slightly damaged concrete, and eliminating minor irregularities before painting or coating. Highly recommended for repair of…
Description KUT EPOXY MORTAR - HB is a special blend of fillers and solvent-free epoxy resin, designed for speedy and permanent repairs to concrete, particularly in vertical or overhead situations. The mixed material is applied to a suitably prepared surface and quickly cures to form an impermeable repair unaffected by most forms of a chemical attack. It is supplied as a three-pack material in pre-weighed quantities ready for on-site mixing and use Uses For speedy and permanent…
Description KUT FAIRING COAT is a concrete-grey or off-white, single-component mortar, based on a blend of portland cement, graded silica sands, water-reducing agents, and compatible water-resistant polymers. The product is designed to give good adhesion and cohesion in a plastic state and low water requirement resulting in low porosity and long durability... Uses KUT FAIRING COAT is used for producing a fair-faced concrete appearance after patch repairs to walls, for leveling uneven…
Description KUT FASTCRETE is a fast-setting concrete patching material composed of special cement, fine aggregate, and selected plasticizing admixture and fibers, requiring the addition of potable water only for mixing. It produces high early strength and achieves the initial set in 20 to 30 minutes, and the final set in 45 minutes. Repaired areas may be opened to traffic in 2 - 2:30 hours. Uses KUT FASTCRETE is specifically formulated as a semi-flowable material for the rapid…
Description KUT FILLET PAK is supplied as a ready-to-use two-component product consisting of a dry powder (Part A) requiring only the addition of the liquid aqueous polymer (Part B) to produce cohesive easily applied mortar. The dry powder is a careful blend of cement, graded sands, Microsilica, water-reducing agents auxiliary/modifying polymer, polypropylene micro fibers, and a polymer (Part B) component KUT FLEXI to enhance the general characteristics of the repair mortar. It is…
Description KUT SUPERCOAT No. I is supplied as a ready to use dry powder requiring the addition of only clean water to produce at the job site a highly cohesive fibre reinforced easily applied repair mortar. KUT SUPERCOAT No. I is formulated on a blend of portland cement, Microsilica, non-metallic reinforcing fibres, selected graded aggregates, water reducing chemicals, shrinkage compensating agents and new technology synthetic resin dry polymers. KUT SUPERCOAT No. I mixed mortar delivers…
Description KUT SUPERCOAT No. II is supplied as a ready-for-use 2-component product consisting of a dry powder and a specially formulated aqueous synthetic resin polymer which after mixing produce a highly cohesive easily applied repair mortar. This product is formulated as a new technology blend of cements, microsilica, non metallic reinforcing fibres, selected graded aggregates water reducing chemicals and shrinkage compensating auxiliary agents. The special liquid polymer KUT FLEXI is…
Description KUT RENCON ‘S’ is supplied as a ready to use dry powder requiring only the addition of water to produce cohesive easily applied mortar. The product is a careful blend of portland cements, graded silica sands, shrinkage compensating agents silica fume, water reducing agents and compatible water resistant polymers. The product is designed to give good adhesion and cohesion in, the plastic state and low water requirement resulting in a non-shrink low porosity mortar with high…
Description It is supplied as a ready to use dry powder requiring only the addition of water to produce a cohesive and easy to apply mortar. KUT OVERHEAD MORTAR is a new technology polymer modified blend of Portland cement, selected graded sands, Microsilica, non-metallic special reinforcing fibres, light weight micro aggregates, water resistant polymer sand water reducing agents. It is formulated for vertical and also overhead applications in outdoor and indoor repair works. KUT OVERHEAD…
Description KUT FLOWCRETE is supplied as a ready-to-use cement aggregate/sand mix requiring only the addition of water to produce a free-flowing repair concrete. It is a careful blend of Portland cement, graded aggregate, sand, micro silica, water-reducing agents, and auxiliary expansive modifying agents to compensate for the shrinkage in both the plastic and the hardened states. Uses KUT FLOWCRETE with dual expansion characteristics has been engineered for a wide range of…
