TILE GLUE AND GROUT

Description

KUT TILE GROUT is based on portland cement, selected sands, special polymers, workability agents, hydrophobic additives and shrinkage compensating agents. It is available in white and a limited range of colours, other colours for special bulk orders by arrangement. The powder is mixed with water to produce an easily worked mortar with good filling properties, allowing joints to be completely filled in one operation. The completely cured grouts is resistance to fungal growth , weather resistant, non-shrink and has excellent water resistance and provides waterproof joints. It is available in three grades: 1. Superfine: White only 2. Normal: White and a limited range of colours for gap widths upto 3 mm. 3. Wide gap: White and a limited range of colours, for gap widths 5-25 mm.

Uses

For internal and external tiling in dry and wet conditions including swimming pools, hospitals kitchens and bathrooms. Can be used with the addition of KUT FLEXIBOND mortar improver to produce tile joints with improved elasticity and water repellency/proofing. Do not use where chemical resistance is required, use KUT EPOXY TILE GROUT In these situations.

Description

KUT TILE ADHESIVE-EG is supplied as a ready to use one component white/grey powder requiring only the addition of water to produce a cohesive, sticky highly adhesive thin bed tile adhesive. KUT TILE ADHESIVE-EG powder is a blend of white & grey cement, selected fine sands, water reducing chemicals, special polymers, water retention agents to enhance workability and ease of application.Available in two colors-White and Grey.

Uses

KUT TILE ADHESIVE-EG white is recommended for following application:(i) Fixing ceramic tiles on walls and floors.(ii) Bonding quarry tiles direct on concrete or sand cement renderings and clean non-glazed old terrazzo tiles. (iii) Fixing tiles over timber and existing vinyl tiles if the surfaces are properly cleaned and primed with a brush coat of KUT FLEXIBOND. KUT TILE ADHESIVE-EG is specially recommended for fixing porous and white coloured tiles. However due care should be taken to ensure proper levels and that the thickness in such application does not exceed 12mm. Both grades of KUT TILE ADHESIVE-EG are suitable for interior as well as exterior conditions.

Description

KUT GP GROUT is a pre-packed cementitious grout requiring only the addition of clean water to produce at the job site nonshrink multi-application grout. It is a special and unique blend of cements, microsilica, graded sands, water reducing agents and special auxiliary chemical to deliver expansion in the plastic state to compensate for shrinkage.KUT GP GROUT can be mixed in a range of consistencies in varying the amount of water used to produce a fluid to trowellable consistency grouts

Uses

KUT GP GROUT is formulated for a wide range of applications such as grouting of machinery base plates - anchor bolts - structural grouting of precast elements - grouting of crane rails also bridge seats - beams and columns - handrails. It is suitable for use in marine environments.

Description

It is supplied as a ready to use powder which is a blend of cements, graded sand, microsilica and a blend of expansive agents. It requires only the addition of water to produce a high fluid - high strength non shrink grout. KUT FLOW GROUT is a unique product designed to give positive expansion in the plastic and early hardened states, producing a low porosity high durability material.

Uses

KUT FLOW GROUT with dual expansion properties is recommended for use in grouting heavy duty machinery base plates - power generators pumps - base plates for electrical pylons and oil storage tanks - columns - crane rails bridge seats - compressors. It is suitable for use in marine environments.

Description

KUT EPOXY TILE GROUT is a solvent free epoxy resin blended with selected fine fillers. It is supplied as a three component system in pre-weighed quantities ready for on-site mixing and use. Two versions of KUT EPOXY TILE GROUT are available. 1. Normal: For working at normal temperatures. 2. Extended Pot life: For working in hot weather conditions above 35ºC

Uses

KUT EPOXY TILE GROUT is a high performance epoxy grout with exceptional chemical resistance for bedding and grouting tiles in heavy duty environments. It is used for a single operation bedding and grouting of tiles on horizontal & vertical surfaces. It is used wherever excellent mechanical properties, high chemical resistance combined with a high standard of finish is required such as in swimming pools, hospitals, kitchens, slaughter houses, soft drink factories and steam cleaned areas..

Description

It is supplied as a ready-to-use powder which is a blend of cement, graded sand, microsilica, and a blend of expansive agents. It requires only the addition of water to produce a high fluid ultra high strength non shrink grout. KUT SUPER GROUT is a unique product designed to give positive expansion in the plastic and early hardened states, producing a low porosity high durability material.

Uses

KUT SUPER GROUT with dual expansion properties is recommended for use in grouting heavy-duty machinery base plates - power generators - pumps – base plates for electrical pylons and oil storage tanks - columns - crane rails - bridge seats - compressors and is recommended especially for a situation where compressive strengths exceeding 75 N/mm2 are required. It si is suitable for use in marine environments.

Description

KUT NON-SHRINK PUMPING GROUT is supplied as a ready-to-use powder requiring only the addition of water to produce a free-flowing grout. KUT NON-SHRINK PUMPING GROUT is a unique product designed to give positive expansion in the plastic and hardened states, producing a low porosity high durability material. It is a carefully designed very fine blend of portland cement modified with silica fume, water-reducing agents, and expansive agents. The product is formulated to produce controlled expansion in the plastic state with low water mixing requirements to minimize segregation delivering high early strength and long-lasting durability.

Uses

KUT NON-SHRINK PUMPING GROUT is used for general-purpose grouting of narrow concrete cracks or gaps between concrete and metal structures. • It is recommended to fill gaps between metal electrical lighting poles base plates and the concrete supporting foundation.• It is used for cable duct grouting in post-tensioned concrete members.• It is used for sealing / filling narrow concrete cracks, grouting machine base plates, stanchion bases, and crane rails. • It is an excellent grout for all horizontal ducts or concrete in situ opened channels installation of pipelines, cables, ducts, plastic conduits, etc.

Description

KUT EPOXY GROUT NO.4 is 100% solid. three-component free flow, non-shrink epoxy grout formulated to provide easy placement. It provides high strength and creep resistance combined with the highest effective bearing area.

Uses

KUT EPOXY GROUT NO.4 is used for all grouting applications especially those requiring chemical resistance and heavy-duty resistance to vibrational and other dynamic or mobile loads. Applications include crane and transporter rails, compressors, High-speed turbines and centrifuges, rock crusher and pulping machines, and other heavy-duty equipment. It can also be used for anchoring steel bars with concrete.

KUT EPOXY AN 500 is a two-component, high strength adhesive anchoring system. The system includes 
injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment. The 
KUT EPOXY AN 500 is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in 
concrete base and solid masonry materials. 

 KUT EPOXY AN 500 Injection Cartridge 3:1 two components   - Pure Epoxy resin styrene free   - Available size: 400ml (side by side cartridge)   

DESCRIPTION 
KUT EPOXY AN 500 Pure Epoxy 3:1 resin is a high performance, two components pure epoxy resin system. Applied 
in one single action this resin will produce a high performance, strong fixing with exceptionally high chemcial 
resistance. 

APPLICATION  - Fixing machines, hardrails, steel constructions, wooden constructions, reinforcement bars, especially suitable 
for big diameter rebar and rods.   - Bonding threaded rod and reinforcing bar into hardened concrete.   - Suitable to resist loads in cracked or uncracked concrete base material for cases where anchor design theory 
and criteria applies.   - Can be installed in a wide range of base material temperatures.   - Medium & Heavy duty load applications.   - High durability.   - Ideal for indoor usage.